What's Old is New Again

While I made a few posts on my mast and boom already, I decided to post something longer to show the progress that went into where the mast is today.


When I moved the boat from Tennessee to Virginia, I had it parked nearby in the neighborhood. I moved the boat to Rockhold Creek Marina a week later. Before the move to the marina, I took the boom off and stored it in the garage at the house for some work. Took the hardware off, and cleaned up a few pieces here and there. I had expected to do all the work myself, but then decided that it would be best to hire some of it out.


I took the gooseneck end off as there was a LOT of corrosion and paint was lifting up and it was just a horrible mess. With two cam cleats mounted on either side, I went to remove them. One of the bolts holding it on did NOT want to come out no matter how much I used the hammer. I used pliers to twist it out but still nothing. The pliers caused the exposed portions of the bolts to shear off. I ended up having to drill it out and knock out the piece that was left after the drilling. Thankfully, drilling it out worked out well. I sanded it down with 80 grit sandpaper to get a lot of the corrosion off and soaked it in vinegar too to hopefully eat away some of it. Of course, I rinsed it down with water as well.


From what I have been able to find online, or rather NOT find, is that these two end pieces on the boom are not available anywhere so it's a good idea, I think, to take care of these before they're too far gone.

Badly Corroded

Drilled out, mostly

Knocked the last piece out

Vinegar soak

I pulled the piece off from the other end of the boom. I removed the lines going through it and set them aside for measuring and replacement at a later date.

outhaul

this is how the outhaul was attached in the boom

Serial number?

Made by Forespar USA

Here, a video showing the boom and hardware placement for the reefing setup.

When the end pieces came back from the rigging shop, they came out very nice. You can still see the pitting from the corrosion that was there but it's so much better than it was before.

Took off all the hardware from the boom. The slide for the gooseneck had a backing bar in the boom that dropped from place when the bolts came out.

When I took off the three reefing blocks, I found electrical tape on the bottom side. I believe this was meant to keep the metal from rubbing and ruining the finish on the boom.

Last piece to remove was attached by rivets.

The mast work to this point has been pretty slow as I work on other projects.

I consulted a shop about fabricating hardware for the mast. Like the tangs holding the standing rigging. It's more for preventative measures since much is still 35+yrs old. I also want the shop to repaint the mast, but the owner said I have to do the grunt work. Meaning, I have to take all the hardware off, pull the wires, running rigging, and even sand it down to bare metal. NO Paint!

Since the boom is already started, I went ahead and pulled the hardware off the mast and started sanding it down. For the end of Aug 2016, it's been going well with lower temperatures.

While already posted, here's the video showing the mast stripped of hardware.

And views of the grunt work:

The start of sanding

almost half way down one side

most of one side sanded. At this point, the sander I borrowed stopped working.

Found this line when I pulled wires, so using it for when it's time to run the wires back.

Since the sander I borrowed stopped working, I used the time to see how a paint stripper would work on getting the paint off the metal. Mainly looking to use it in the cracks/corners where the welds are. I thought it worked out well for the most part. Just have to wait for it to do the work.

The square is from the old Forespar factory sticker.

The mast step itself also had work done to it. Here, you can see the wire connections were made on deck. The rigging shop doing the work on the mast insisted all connections need to be made below, in the cabin. So he took the mast step and added a tube to it that would allow wires to be routed below deck.

While the mast, boom and spreaders were at the shop, they did a few modifications. They added a post by the mast head to move the location of the tri-color/anchor light. They patched up some holes for old hardware that was no longer needed and cleaning up some of the corrosion. The antenna connector was replaced and moved to a new location as well. Inside the mast, the rubber flap used for the wiring was taken out and a new conduit was installed. Main reason for this was some of the wires for the light by the spreaders crossed by the halyards

I went to the shop to see the work that was done, and to reattach the hardware myself with the shop owners help using their compressor and riveting tools.

the boom

I'm really happy with how this project turned out. A few people I mentioned this to were a bit surprised that I wanted my mast to be bright yellow and even talked me into other options... white (like everyone else), bare aluminum (which is still protected anyway.... but still, boring) and even one who suggested black stripes with the yellow going the full length, like hazard tape.


My boat will certainly stand out in an anchorage and will be easy to tell people to "find the boat with the yellow mast" in order to find my boat. :-)

And lastly, I wanted to mention that the work was done by Eastport Spars and Rigging in Galesville, MD. John, the owner, and his crew did a wonderful job. Many suggestions and discussions to make sure things were done the right way. Awlgrip products were used in the paint process and the color is Federal Yellow.

Getting Wired Part 2

It has been a good weekend. In an update to the previous post, I did some more wiring on the boat.

Spent a few hours today working on actually mounting/installing the Pronautic 1230P charger I bought TWO years ago. I recently ordered a couple of Firefly batteries for my new house bank. Since I want to make sure the batteries are taken care of, I had to get the charger set up. I ordered some 10/2 wire and some ring terminals from Genuinedealz to connect the charger to the batteries. While time consuming, it wasn't too difficult. I mounted the charger to a couple pieces of oak I had laying around and went head first into the starboard quarterberth to mount the setup to the bulkhead. A little tight but manageable.

I routed the new wires the same way they were with the old charger directly to the battery bank. When I flipped the breaker on the panel to turn on the charger, a fan started and in a moment, a click started charging to the batteries. Very happy this worked out. I don't have a starting battery yet and will run wires for one when the time comes. When I left the boat today, I turned on the vent fan that came with the Airhead for ventilation. The Airhead website said the fan draws .08 amp. So I figured even leaving it on for the week, or even two weeks, it wouldn't drain the battery too much, too fast. And now the charger is in place, I can top off the batteries during my visit.

In my last post, I mentioned ordering a panel from Front Panel Express using their software. Well, it came in and I'm pleased with how it turned out. Black anodized aluminum with engraved letters filled in with yellow, 7"w x 3.25"h. Everything lined up nicely for the toggle breakers. I'd say this was a good test panel for the possibility of changing the main breaker panel by the companionway. Changing the main panel isn't a near-term project but something I can play around with in the design in the meantime.

First look in the box. Vacuum sealed on cardboard.

only have two breakers at the moment

got a bus bar made for attaching the main positive line

This panel will be mounted just under the front of the nav desk where an old cassette car stereo was mounted. This will be used to wire the VHF in its new location, just above the nav desk. Later, perhaps other items. At least it won't require multiple wires to be sent back the main panel, keeping the wiring clutter to a minimum.

Lastly, the mast. The shop I'm having do a paint job is also doing a few modifications. They changed the setup by the masthead. This will help keep wires and halyards from interfering with each other. They're changing the location of the conduit for running wires up. Instead of being on the back side where the track is, they installed a new one on the front side of the mast.

The anchor/tri-color light was in the middle of the masthead and now on its own pedestal on the side. The wires will run up the middle of the tube instead of being external. They also patched up a lot of holes, the largest being the hole from the baby forestay that I didn't intend on using and also a hole used for a box sheave. They patched up a few smaller holes around the mast and boom that were mostly unused. A new location for the VHF antenna is also installed. Soon, it will be sent for painting and then the hardware will be reinstalled.

The guy at the rigging shop suggested connections shouldn't be outside of the boat. So he's talking about putting a short tube on the mast step that will go down a bit (maybe 1") into the deck. Then connections would be made inside the boat at the bottom of the compression post. I'll still have to see how big the holes are at the bottom of the compression post to see how feasible it would be for any connectors to pass through. Below is a picture of a tube on the mast step at the shop I used to visualize what it might look like. The final product certainly wouldn't be as high as in the picture. Should be shorter that would still allow the mast to be stepped/unstepped by an owner.

 At this time, not much to update in regards to the insurance claim on the fallen tree hitting the boat. I've been told I need to contact workshops to get detailed quotes for getting the damages fixed.

Lately, I've been side tracked, or maybe distracted, from a couple projects due to focusing on the mast and the tree damaging the boat. I hope to get back on track and tackle the major projects I've been working on over the summer that still isn't quite done yet.