Showing posts with label repair. Show all posts
Showing posts with label repair. Show all posts

Saturday, June 17, 2017

Finishing the Tank

Here's the latest update.

In total, I painted three coats of 2-part epoxy paint alternating between white and grey so I could make sure I had good coverage with each coat. Last week, I painted on a sealer/liner by KBS Coatings that takes 4 days to fully cure. No problem since I visit the boat once a week. Looking at the tank yesterday (16 Jun), I'm happy to report the sealer worked out really nice and is a very hard surface inside the tank. Even has a bit of a gloss look to it too.

In the meantime, I've been working to drill and tap one of the inspection plates for the fittings to feed fuel to the engine and the return. I still need to install a fitting for the vent but need to make sure I measure what I need first.

The only other thing I need to do is also install a fill port and this project will finally be done. It has taken a little more than a year to work on this one project, mainly because of only being able to visit once a week. While there have been some very frustrating moments during this project, I'm very happy now that this project is coming to an end. Soon, the engine will be back on board and other tasks will be completed in order to get the boat ready.






I shot this video to show the interior with the sealer/liner painted on and how hard the material is.



Here's a picture of how the tank looks today. Inspection plates with fittings installed, minus the fill port.




I know this is a very crazy idea to have built a fuel tank out of fiberglass and I know of only one other NS27 owner who did it. Now, the real test will come once the last pieces come together and fuel is poured into it.

Monday, June 6, 2016

It's Getting Hot in Here

Getting hot on the boat lately. The work I'm doing on the boat now requires a tyvek suit which is making it feel hotter. Decided to install an air conditioner in the forward hatch to cool things down. After a day of using it, I'd have to say that it's better than nothing. While it's only marginally cooler, it does help make it more bearable inside.

Looking at using this only as my refit continues during the summer.





Sunday, December 13, 2015

State of the Engine

As I'm looking over the engine, I took pictures to show how much work will need to be done. The main areas of visible damage seem to come from a few sources but that has cascaded into more work elsewhere. As they say, everything rolls down hill. For example, it looks like the gasket for the exhaust mixer failed so that caused rust going down to the zinc below it, likely to the fuel pump below that, and made its way toward the dipstick. I at least haven't seen any water when doing the last oil change, but that was a few years ago by now. That side zinc won't budge right now so some extra work will be needed there.

Another area at the back at the aft zinc (there's only 2 on this engine), there's some oil there. I believe this is from the failed valve cover gasket that I had fixed before. That zinc cap won't budge either. I have PB Blaster I can use to see if that will help.

Water had previously leaked from the engine panel down to the top/front of the engine. That shouldn't be too bad, but will still need some cleaning up. The thermostat cover seems to have had a leak before too, and I'm looking to replace that and the mounting bolts/gaskets and maybe the thermostat itself. Another Nor'sea owner suggested I remove the injectors just so that I can. Otherwise, doing it later can be a pain. But, if I'm not able to, it may have to be removed at a shop anyway. Other hoses, pipes, gaskets, and bolts will be replaced as well. I have a parts catalog and shop manual on hand on the computer and will be going over them to get a list together.

Just the engine itself is plenty of work. But the main reason I pulled it out in the first place, was to replace the fuel tank, which has just begun.

current state in the cabin

exhaust elbow, below is one engine zinc

the other engine zinc



fuel pump

surface rust hasn't been there long


thermostat cover

the rust line coming from the exhaust mixer above

fuel pump to the left, side zinc in the center

exhaust mixer mounting



thermostat cover again, to be replaced w/bolts



inside of exhaust mixer



Not much, but it's a start to removing the fuel tank. Doesn't look to me like fiberglass was used, just resin holding the tank. Some parts was maybe 1/8" thick and the aft area was closer to 1/4" or slightly more. Using an oscillating cutting tool, a screw driver, and a 3lb sledge hammer, it's coming out well enough. Then, the foam underneath will be torn out as well.





Saturday, November 21, 2015

Slow Work Day

Slow day this weekend. Not a whole lot of work on the boat. I spent more time chatting with a couple other guys who are about to head out on their boats down the ICW to Florida. Not really with the snow bird crowds but moving there.

I did some measuring of hoses to see what I may need. The cockpit drains have a white plastic hose that I'm thinking to replace with rubber wet exhaust hose. My reason is that the hose clamps can get better compression onto the seacocks. Speaking of which, I found out one of the seacocks has worked loose due to the wood backing plate getting soft. Good thing they're getting replaced anyway. The only other work I did was to drill out a couple small holes on the deck that had failed patches and filled them in with thickened epoxy. I also had a quick look at placement of the access ports for the water tanks.





Safe travels to all these coming weeks.