I finally got to Rhapsody today. As noted on a previous post, I had a bolt that didn't want to come out of the starboard handrail. I was going to use a fine tooth saw blade like used on a hack saw but that didn't really work out. I went to the hardware store and bought a small 12v cordless drill. The bit I used was as big as the threaded part of the bolt so it wasn't oversized. I drilled from down below where the head of the bolt was at. Once it went through the head enough, I used a screw driver and popped the head off. I went back to the top and pulled the handrail right up. It was easy, I should have tried doing that earlier.
Now I have the handrail at the house, along with the other two pieces from the port side for sanding and refinishing.
My goal with the handrails is to scrape off the old varnish, refinish with several coats of fresh varnish then rebed the rails back on the boat. As of now, I'm looking at bedding down with butyl tape. Once this is done, then I can get a survey, insurance and take it up to a marina where I have reserved a slip.
Here's a picture of the bolt after I popped the head off and a picture of the whole bolt after I removed the whole rail.
Showing posts with label butyl tape. Show all posts
Showing posts with label butyl tape. Show all posts
Saturday, September 29, 2012
Drill Time
Labels:
butyl,
butyl tape,
Epifanes,
Epifanes Varnish,
Marina,
Nor'sea,
Nor'sea 27,
sailboat,
sailing,
teak,
varnish
Saturday, August 25, 2012
Handrail Removal
I decided to do a video this time showing my removal of the handrails.
One of the bolts I could not wedge the nut to loosen and I stripped the head trying to get it out. Now, it looks like I'm going to have to resort to drilling out the bolt or get a small fine tooth saw blade and cut the head off so I can remove the rail.
The rails I did get off are now at the house so I can refinish and prepare them for reattaching to the deck. So far, things seem to be going well. Just need to get that one bolt out so I can get to work on the other handrail.
Considering the bolts are phillips head, I'm now considering the possibility of changing them to a hex head. I wonder if that might make it easier for removal in the future, if it was needed. Either way, as long as things get bedded down good in the first place, it should be good as it is. If I'm going to drill out or cut the one bolt off, I'll need to find a replacement anyway for that one.
One of the bolts I could not wedge the nut to loosen and I stripped the head trying to get it out. Now, it looks like I'm going to have to resort to drilling out the bolt or get a small fine tooth saw blade and cut the head off so I can remove the rail.
The rails I did get off are now at the house so I can refinish and prepare them for reattaching to the deck. So far, things seem to be going well. Just need to get that one bolt out so I can get to work on the other handrail.
Considering the bolts are phillips head, I'm now considering the possibility of changing them to a hex head. I wonder if that might make it easier for removal in the future, if it was needed. Either way, as long as things get bedded down good in the first place, it should be good as it is. If I'm going to drill out or cut the one bolt off, I'll need to find a replacement anyway for that one.
Saturday, August 18, 2012
Teak handrail work
For the first time in a long time, I have a birthday on a day that I'm NOT working (as in, paid employment). Yep, today I'm 34.
It was a nice day today, and being a weekend, I decided to go do some work on the boat.
I've been looking at the teak handrails for a while and doing a little work to rebed them to prevent additional damage to the interior. I guess you could say that today I had a crazy moment and decided to ruin the nice handrails down below, gut out the plugs and unscrew everything so I could get to the bolts holding down the handrails on the top.
Here is the nicely finished plug down below.
And here's how it looked after I took one of them out.
Everything was going pretty well. Still, it wasn't easy. My hand are hurting from trying to chisle everything out with screw drivers without causing too much damage during the removal.
One of the plugs on top had to be removed in order to stop a nut from spinning with the bolt.
I ended up having to use a painters spatula to wedge it to keep it from moving. At the same time, I was reaching in from below through a port hole to unscrew it.
Here's the handrail sitting in the cockpit.
It'll take some cleaning up to do before I put the handrails back on. These, I can bring back to the house to pull the old varnish off without having to go out to the storage place to work on it at the boat..
Unfortunately, The handrail on the other side was not as cooperative. There were three small handrails down below that I had to chisle out the plugs to get to the screws. Even then, When I worked on the bolts to detach everything, I have one that is spinning freely like the one I mentioned above and three of them are pretty tight and don't want to move and will require a bit more work to get it off. Since I wasn't feeling up to staying at the boat any longer, I thought it best to try again another time, probably next week. All together, I probably spent about 5 hours on all this today. It is not easy work cleaning the plugs out of the handrails.
Another reason I decided to do all this is so I can rebed everything rather than focusing on just where I see damage. This seems to be the first time they will be rebedded in 30 years or so. Then, I have to decide, do I use Butyl tape or Lifecaulk to rebed everything, as this is what I have on hand. Or, as others on the Nor'sea owners group seem to love, Dolphinite, which I also have on hand. I'm not sure of Dolphinite as it seems to have a more fluid consistancy that I expected. I first thought it would be similar to the butyl putty feel to it.
Time to consult the group. Thanks for visiting.
It was a nice day today, and being a weekend, I decided to go do some work on the boat.
I've been looking at the teak handrails for a while and doing a little work to rebed them to prevent additional damage to the interior. I guess you could say that today I had a crazy moment and decided to ruin the nice handrails down below, gut out the plugs and unscrew everything so I could get to the bolts holding down the handrails on the top.
Here is the nicely finished plug down below.
And here's how it looked after I took one of them out.
Everything was going pretty well. Still, it wasn't easy. My hand are hurting from trying to chisle everything out with screw drivers without causing too much damage during the removal.
One of the plugs on top had to be removed in order to stop a nut from spinning with the bolt.
I ended up having to use a painters spatula to wedge it to keep it from moving. At the same time, I was reaching in from below through a port hole to unscrew it.
Here's the handrail sitting in the cockpit.
It'll take some cleaning up to do before I put the handrails back on. These, I can bring back to the house to pull the old varnish off without having to go out to the storage place to work on it at the boat..
Unfortunately, The handrail on the other side was not as cooperative. There were three small handrails down below that I had to chisle out the plugs to get to the screws. Even then, When I worked on the bolts to detach everything, I have one that is spinning freely like the one I mentioned above and three of them are pretty tight and don't want to move and will require a bit more work to get it off. Since I wasn't feeling up to staying at the boat any longer, I thought it best to try again another time, probably next week. All together, I probably spent about 5 hours on all this today. It is not easy work cleaning the plugs out of the handrails.
Another reason I decided to do all this is so I can rebed everything rather than focusing on just where I see damage. This seems to be the first time they will be rebedded in 30 years or so. Then, I have to decide, do I use Butyl tape or Lifecaulk to rebed everything, as this is what I have on hand. Or, as others on the Nor'sea owners group seem to love, Dolphinite, which I also have on hand. I'm not sure of Dolphinite as it seems to have a more fluid consistancy that I expected. I first thought it would be similar to the butyl putty feel to it.
Time to consult the group. Thanks for visiting.
Labels:
boat,
butyl,
butyl tape,
deck,
Dolphinite,
Epifanes Varnish,
handrail,
lifecaulk,
mineral spirits,
Nor'sea,
Nor'sea 27,
Rhapsody,
sailboat,
sailing,
teak,
Tour,
varnish
Subscribe to:
Posts (Atom)







