Showing posts with label Vetus. Show all posts
Showing posts with label Vetus. Show all posts

Saturday, August 9, 2014

Glassed In Bolt

Here's a video of the Airhead toilet I installed. It's more of a review to show how I have it installed as my head compartment is not very big. I find it is a good fit for my boat.


I spent most of the day trying to remove panels in order to remove just ONE chainplate. The panels were long so I couldn't pop them out or slide them out of the way once the screws were removed. So, I took a Dremel and cut one piece enough to get a small fine toothed saw blade into the cut so I could cut down on other pieces to expose the bolts. I had an interesting surprise when I removed them. The bolt on the very bottom of the chainplate, was glassed in. I used a different bit on the Dremel and cut away the fiberglass around the bolt enough I could get a wrench around it to move it. Once the fiberglass was cut away, the bolt was easy to remove. The top bolt was harder to remove since it was up and behind another panel. The little shop-vac was necessary anyway to draw enough amps from the 1000W inverter on the truck for the Dremel to work. In a way, it almost felt like doing dentist work with the drill and suction. Sounded about the same.

Used Dremel on top panel that was cut

Used this blade to cut the rest by hand.







A couple more chainplates, and I'm done with taking them off the boat. I'll have to do the same process for the last port side chainplate. I also took the tiller off the boat to bring home and will put a couple more coats of varnish on it. Mainly to clean up a few scuffs. I was going to bring the rudder cheeks home too to refinish but decided that can wait for now.

I was looking at some info online about hulls and gelcoat and it got me to thinking about how nice of a finish others have on their boats. Looking at my boat, I would say the gelcoat is in really good condition. Looks nice and smooth. I'm thinking to use some compound and wax to get a nice shine on the hull. I may be able to just do a test spot to see how just a compound/wax would do before going through the entire boat.

Sunday, June 1, 2014

Deck Vent Work Finallized

A trip to the boat turned out to be a good day. I finished some work on the vent. I took the tape I had around the vent off and cleaned up a bit of the bedding that had squeezed out. I used some wood plugs and filled the screw holes. Two of the holes were deep enough I was able to put them in easy enough and two others needed to be cut down. I put a couple coats of varnish on it too. Toward the end of the day, it had rained so the water beaded up nicely. I plan to apply more coats but this is a good start to protect the wood.
 
 


 
 Most of the exterior wood has turned grey. There's still some old varnish still flaking off. Some time, I'd like to finish the rest of the exterior wood. I had a bottle of Teak Cleaner so I wanted to see how it would work on the grey wood. I started off with a test spot but then spread over most of the port side. I like that it turned out well. It might work well in getting it refinished.
 

Wet from rinsing with fresh water
 
 


Transition between grey and cleaned teak
 I want to get the Airhead ready to use. Then I can go for a weekend sail and stay anchored out. I took one of the two coir bricks and added water while in a 5 gallon bucket. I broke it apart as it absorbed the water. The brick ended up expanding to fill half of the 5gal bucket. I didn't put any of it in the toilet but left it so it will be ready to go. Now, the only thing I really need to do is to wire up the fan for ventilation and it's ready to go. I might do something for a temporary setup until I can set it up better but I'll have to see what I'm able to find.
 
 
At one point, I was adding the second coat of varnish around the vent. One of my dock neighbors who was around decided to check out how everything looked and got to talking. I set down the cup of varnish and next thing I knew, I saw it had spilled over onto the deck. Not too crazy about it so now I need to find a way to get it off. I've already been suggested to try a heat gun and/or acetone or some other solvent. Hopefully I can get it cleaned up and looking nice again soon.
 
Just goes to show you not everything turns out great.
 

Apparently the neighbor makes suggestions saying certain things are not good for when I sell the boat. He said having a composting head would make it hard to sell. Today, he saw a small amount of varnish and run off of the vent base and said it would make it hard to sell the boat.

And NO I'm NOT selling my boat.

Sunday, May 18, 2014

New Hole in the Boat

Previously, I was working on getting a block of wood to the curved shape of the cabin top. I cut away much of the material that I didn't need. I tried sanding it but the paper was loose so it didn't work out well so I got another sheet of 60 grit and taped it down to keep it from moving. This worked out well and took quite a bit of material off that smoothed it out.
 


 
Today was a very busy and productive day. I got a lot more done than I thought I would. I originally thought I would only be able to install the vent on the cabin top. It was a bit nerve racking since I was about to drill a new hole in the boat. To get an idea of placement, I placed the fan housing from the Airhead toilet on the ceiling to see how much bend there was in the hose.
 



I used a 5/16 bit to drill out the four corners to mount the wood block, but not all the way through. This allowed the  #8 screws I got to be countersunk below the surface. I used a smaller bit to drill through the rest of it, then the pilot holes into the cabin top.




I taped around where the block was being mounted. I also used tape around the block. I used Dolfinite bedding compound to bed the block onto the deck. Dolfinite has been recommended by other Nor'sea owners numerous times so I thought I would give it a try this time. A dock neighbor suggested I use 5200 or 4200 and said he never heard of Dolfinite. I wasn't about to go buy another type of sealant.


 
 


After using the Dolfinite, I smoothed it out on the edges and removed the tape. I wonder if I should have waited for it to setup before removing the tape but it seemed to work out well. I then used a 3 inch hole saw to cut out the center of the block. Turns out the cabin top is about 1 1/2" thick.




Nice skylight





I mixed up some epoxy. I used it to coat the interior of the cutout of the deck only, not the wood block. I only used it for a single coating.




The vent I got is a Vetus Mushroom vent. I took the base and drilled pilot holes for the screws I got at the nearby shop.



I also used Dolfinite on this too. I put some of it in a ziplock bag and cut the corner out of it to spread it out a little at a time without putting too much on. After placing the vent base back on, I decided to leave the tape in place this time. I also put the top piece of the vent in place and the knob that is installed from underneath.







I put the fan housing over the hole that was drilled out. The surface was flat enough, I didn't need to put anything else over the hole to mount the housing. I also ran the vent hose like the second picture at the top and it reached where it needed to on the head.


I mounted the head and the liquid tank onto the base. There wasn't much clearance for the mixing handle so I may cut that short for it to do complete turns.



There's only a few other things that need to be done to complete the install. I need to connect the wires for the fan that's mounted in the housing, install plugs on the wood block to seal the screw heads, connect the vent hose to the head and then it's pretty much ready to use.