Showing posts with label Composting. Show all posts
Showing posts with label Composting. Show all posts

Sunday, June 1, 2014

Deck Vent Work Finallized

A trip to the boat turned out to be a good day. I finished some work on the vent. I took the tape I had around the vent off and cleaned up a bit of the bedding that had squeezed out. I used some wood plugs and filled the screw holes. Two of the holes were deep enough I was able to put them in easy enough and two others needed to be cut down. I put a couple coats of varnish on it too. Toward the end of the day, it had rained so the water beaded up nicely. I plan to apply more coats but this is a good start to protect the wood.
 
 


 
 Most of the exterior wood has turned grey. There's still some old varnish still flaking off. Some time, I'd like to finish the rest of the exterior wood. I had a bottle of Teak Cleaner so I wanted to see how it would work on the grey wood. I started off with a test spot but then spread over most of the port side. I like that it turned out well. It might work well in getting it refinished.
 

Wet from rinsing with fresh water
 
 


Transition between grey and cleaned teak
 I want to get the Airhead ready to use. Then I can go for a weekend sail and stay anchored out. I took one of the two coir bricks and added water while in a 5 gallon bucket. I broke it apart as it absorbed the water. The brick ended up expanding to fill half of the 5gal bucket. I didn't put any of it in the toilet but left it so it will be ready to go. Now, the only thing I really need to do is to wire up the fan for ventilation and it's ready to go. I might do something for a temporary setup until I can set it up better but I'll have to see what I'm able to find.
 
 
At one point, I was adding the second coat of varnish around the vent. One of my dock neighbors who was around decided to check out how everything looked and got to talking. I set down the cup of varnish and next thing I knew, I saw it had spilled over onto the deck. Not too crazy about it so now I need to find a way to get it off. I've already been suggested to try a heat gun and/or acetone or some other solvent. Hopefully I can get it cleaned up and looking nice again soon.
 
Just goes to show you not everything turns out great.
 

Apparently the neighbor makes suggestions saying certain things are not good for when I sell the boat. He said having a composting head would make it hard to sell. Today, he saw a small amount of varnish and run off of the vent base and said it would make it hard to sell the boat.

And NO I'm NOT selling my boat.

Saturday, March 8, 2014

Head Space and Timing

A week ago, there was a nice little weather system that went through the area dropping about 4 inches of ice and then a little snow on top of that. The last couple days, it was starting to warm up enough to melt the ice. Today turned out to be a very nice day with a high of 60F. A visit to the boat turned out well although there were always more to be done.

There was still ice on the dock and the boat. I had to use a boat hook to chip away at the ice on both to get rid of it. The cockpit had about 4-5 inches in areas that I broke up and threw into the lake. By the time I left, the ice on the dock was gone and there were still a little bit on the boat in the shaded parts.



One thing I wanted to do was to measure the space on the deck in preparation for venting and getting ready for a new head whenever I'm able to get one. After clearing the ice on the deck, I was able to see the space I had to work with.


The space I have for vent placement is between the handrail and the line shown in the picture above. My original idea for venting was to use a solar vent in place of the waste deck plate. There are many boats that have these solar vents and a couple of them, I could hear the fans spinning as I walked the dock. One downside to these is the size of them. At 9" overall width, it seemed to take up a lot of space. After measuring the space I had, it would be too big anyway.


Vent on another boat

While talking with others about this idea, it was suggested that I use a dorade box with a cowl vent. I looked into these and getting the idea that this could work but started to think that maybe the size would be more than I would like. Here are examples of dorade boxes on other boats in my marina.




These dorade boxes allow air flow into the cabin of the boat while draining water back out through holes along the bottom edges. Instead of these large boxes, which would be near the cockpit, I decided to go with something a little lower profile that wouldn't stand so high by using a Vetus Mushroom vent along with a block of wood used to mount it on shaped to the curve of the deck.

The idea would look something like this:


On the inside, placement would have to avoid the light on the ceiling, but also allow the placement of the hose that it's not in the way either. I'm not too crazy about drilling a large hole in the deck but I think it would be useful for venting. In this picture below, I'm looking at placement just off the third handrail bolt.


Routing the hose would keep it along the back wall toward the head.


Since taking out the old head, I have been left with a hole from the holding tank. I recently got a board that is sold as a tool box cabinet top. I cut it to the size I needed and I thought it turned out pretty good. I have space where I could drill into the board and the mounting surface and bolt it down. I'm thinking I could use a caulk to seal it when it's bolted. I've also had the idea to paint it over, after sanding to rough it up a bit, with bilgekote to protect it too.



I also have a little bit of the cut off material that could be used for the back edge. I'll also have to clean the back wall and/or paint over it.


When I took the head hoses out, I broke part of a fitting that was used for venting of the holding tank. I wanted to remove it so I took a couple wall panels off and attempted to take it off but it didn't work out. I ended up breaking the exterior part of the vent off but nothing else would move. I didn't have the supplies with be, but I was going to mix up some epoxy and fill it in. Then, if/when I get to it, I was going to repaint the sheer stripe on each side.

The fitting that broke with the hose.
 



Didn't take much for it to break.
The panels didn't seem very easy to remove and I don't expect doing that again anytime soon, at least, not in the head.

Last thing I was going to do, but also didn't work out as planned, was to service the Racor 500's. There's two of them. The one on the port side didn't look too bad but it was the one I was going to do first. At first, the lid wouldn't come off but had to pop it off with a rubber mallet. Then, I was going to remove the little bolts holding the bowl in, then realized I didn't some tools that I don't currently have. So that project is on hold for now. The starboard side looks to have more debris so I hope to clean that one up soon too.

Port Side

Starboard Side

One of the bolts I need sockets for.
With that, there wasn't anything else I had plans to do so I packed up and went back home.

Overall, it was a nice day. There were other people at the marina getting their boats ready to sail. I also met a guy a couple docks down who said he was from Poland. His English wasn't too good so we didn't talk long. He was also busy breaking ice off the dock.

Spring will be here soon and it's about time!

Sunday, February 24, 2013

REFIT Plan: The Head

Looking to change the head to a composting head. I've been wondering how they are supposed to work and how well and been researching it. Seems that anyone who has one is glad they made the change. There are two companies I've come across, Nature's Head and Airhead that seems to have the main products.

The main concern I have is that it seems both of them require a vent through the deck. I'm not too crazy about putting another hole in the deck and where the head is, lines between the mast and the cockpit go right overhead. As I'm writing this, I'm thinking I might be a little creative in the vent. Maybe not going straight up but maybe somehow route a vent toward the stern of the hull. Looking closer at the Nature's Head website, it might be possible to use the deck pump out port location for the air vent since the hole is already there.


Along with conversion to a head, that means no pipes to worry about. I can remove them and likely gain  a little bit of storage space. While I'm looking at replacing all the seacocks in the boat, I may still be able to replace the one for the head in case I, or someone else, decides to install a regular marine head. The deck waste outlet will still be in place which I could re-seal that to make sure it's water tight.

I welcome any thoughts.

Here are the pictures of current setup. I didn't have a tape measure when I took these pictures but I'm hoping one of the composting heads would fit in this space without any issues. It would be nice to free up space by getting rid of those pipes.