This past weekend was very productive. I got some work done on the electric bilge pump. Everything was previously mounted on a wooden board but got a piece of plastic board and remounted everything on it. The pump is at the bottom, with the float switch just above it. The next float switch, I used a yellow plastic scraper to mount, is for the bilge alarm. At the top, you can see all the wires, it's a relay switch. For the most part, everything is mounted the way the boat came. If you look closely at the closeup of the wiring/relay, you'll see a yellow and brown wire that isn't connected to anything. It was previously wrapped in electrical tape. It goes to the bottom float switch but no idea of its purpose. It's kept tied high from any possible water contact.
I still want to work on the manual pump by replacing the rubber pieces but the screws holding the flappers inside the unit doesn't want to budge. Going to try spraying some PB Blaster to see if that will help loosen things up. Otherwise, there doesn't seem to be much I can do with it.
After the bilge pump, I worked on mounting the base the Airhead is sitting on. All this time I've had the Airhead, it wasn't really secured. I had a small tube of LifeCaulk on hand, put a bead of it around the hole the old holding tank sat in, then screwed down the base. The vent hose was also not attached to the Airhead itself. I haven't used the head yet, so didn't have a need to. I got the hose cut down enough to connect everything together and now it's ready to use.
Didn't get any other pictures, but this is just screwing down the Airhead base. Predrilled the base for the screw to pass through but a smaller hole drilled below for the screw to bite into.
Showing posts with label Bilge Pump. Show all posts
Showing posts with label Bilge Pump. Show all posts
Monday, June 10, 2019
Tuesday, June 25, 2013
Tragedy Strikes
Guess what?
There's an issue with the boat.
Here's how my day went with the boat.
This morning, I saw the marina webcam showing my boat at the yard dock. I gave a call to confirm they were ready for me to move it to my slip. This picture shows the boat in the lower left.
In the middle of the picture, by the buildings, is the fuel dock. After work, I drove the hour to the marina to move the boat. I got a couple new dock lines from the truck and took them to the boat. I started the engine, uncovered the tiller, untied the dock lines, then motored over to the fuel dock. I loaded up the fuel tank with 10.38 gal of diesel. I know I put in 5 gal before and there was still some fuel in the tank so I'm guessing the tank isn't as large as I thought. So it's probably 20gal.
Anyway, after I filled the fuel tank, I motored over to the slip. I just missed it and had to back up and try again but it worked out. It takes some time getting used to the tiller. While I was at the slip, I sorted the dock lines and making sure the boat wasn't too far forward causing the bowsprit to get in the way of the walking space on the dock. I routed the shore power cable to the bow and connected to the power box for charging but didn't get to turn the power on in the boat.
Here I got dock lines sorted.
Looks good among the other boats at the dock.
Now, where the bad part comes in. While I was looking things over, browsed at the bilge. It looked orange. I was reminded of a picture I saw on a Cruisers Forum post. While I thought of it, I wiped down the front of the tank, where a piece of wood (or something else) was epoxied into place. I noticed some weeping through and further down I noticed some drips. I couldn't see anywhere else where there was a leak like from the water. Looks like I got a fuel leak. I made sure the bilge pump was turned off at this point to make sure I wasn't inadvertently spilling fuel
This picture shows where it looked to me that the fuel was leaking into the bilge. After wiping it up, I saw very slowly it would get wet again to start dripping.
To show just how much of a pain it would be to replace the tank, this shows how it is mounted. From the opening panel, under the engine, toward the back of the boat. It would require removal of the engine, and possibly the floor to get to it.
So with that, I got things ready again and pulled out of the slip and motored back to the boat yard dock. Gary, the guy I mentioned earlier, said they would help in some way. Right now, I'm thinking I might as well put it back on the trailer and get ready for a lot more work. I'm thinking the refit I was planning to start in a couple years may have just been moved up in scheduling. I was thinking to work over the planned refit over a few years. I've been working on a list of projects so it'll take some time to go through it all. Other than the fuel tank, there's refinishing the mast, new chainplates, new chartplotter, and much more to keep me busy.
I did at least enjoy motoring around the marina, although it would have been nice to do more than a few minutes here and there only to pull it back out of the water soon. I'll send an email in the morning to Gary and see what he says. I'm hoping they will at least be able to drain the fuel tank for me.
Last view before I left this time. Sad, I know, but some things like this is needed. At least doing a refit, it will allow the boat to last much longer. We'll see how it goes.
There's an issue with the boat.
Here's how my day went with the boat.
This morning, I saw the marina webcam showing my boat at the yard dock. I gave a call to confirm they were ready for me to move it to my slip. This picture shows the boat in the lower left.
In the middle of the picture, by the buildings, is the fuel dock. After work, I drove the hour to the marina to move the boat. I got a couple new dock lines from the truck and took them to the boat. I started the engine, uncovered the tiller, untied the dock lines, then motored over to the fuel dock. I loaded up the fuel tank with 10.38 gal of diesel. I know I put in 5 gal before and there was still some fuel in the tank so I'm guessing the tank isn't as large as I thought. So it's probably 20gal.
Anyway, after I filled the fuel tank, I motored over to the slip. I just missed it and had to back up and try again but it worked out. It takes some time getting used to the tiller. While I was at the slip, I sorted the dock lines and making sure the boat wasn't too far forward causing the bowsprit to get in the way of the walking space on the dock. I routed the shore power cable to the bow and connected to the power box for charging but didn't get to turn the power on in the boat.
Here I got dock lines sorted.
Looks good among the other boats at the dock.
Now, where the bad part comes in. While I was looking things over, browsed at the bilge. It looked orange. I was reminded of a picture I saw on a Cruisers Forum post. While I thought of it, I wiped down the front of the tank, where a piece of wood (or something else) was epoxied into place. I noticed some weeping through and further down I noticed some drips. I couldn't see anywhere else where there was a leak like from the water. Looks like I got a fuel leak. I made sure the bilge pump was turned off at this point to make sure I wasn't inadvertently spilling fuel
This picture shows where it looked to me that the fuel was leaking into the bilge. After wiping it up, I saw very slowly it would get wet again to start dripping.
To show just how much of a pain it would be to replace the tank, this shows how it is mounted. From the opening panel, under the engine, toward the back of the boat. It would require removal of the engine, and possibly the floor to get to it.
So with that, I got things ready again and pulled out of the slip and motored back to the boat yard dock. Gary, the guy I mentioned earlier, said they would help in some way. Right now, I'm thinking I might as well put it back on the trailer and get ready for a lot more work. I'm thinking the refit I was planning to start in a couple years may have just been moved up in scheduling. I was thinking to work over the planned refit over a few years. I've been working on a list of projects so it'll take some time to go through it all. Other than the fuel tank, there's refinishing the mast, new chainplates, new chartplotter, and much more to keep me busy.
I did at least enjoy motoring around the marina, although it would have been nice to do more than a few minutes here and there only to pull it back out of the water soon. I'll send an email in the morning to Gary and see what he says. I'm hoping they will at least be able to drain the fuel tank for me.
Last view before I left this time. Sad, I know, but some things like this is needed. At least doing a refit, it will allow the boat to last much longer. We'll see how it goes.
Sunday, May 6, 2012
Many Projects
This weekend was pretty busy. It started out rainy with some lightning/thunder. Not long after I did some videos around Rhapsody, the sky cleared up, the sun came out and it was HOT. Still, I pressed on getting some work done around the boat.
Labels:
Bilge,
Bilge Pump,
Flax,
LED Lights,
Nor'sea,
Nor'sea 27,
sailboat,
sailing,
Stuffing box,
transducer
Saturday, April 28, 2012
Sunny Day
Today was a nice day so I did some work at the boat.
First thing I did was to replace the battery switch. It went pretty good. One cable seemed to be slightly short so it was difficult to reach the connection. Because of how the cables were connected, it ended up being mounted upside down. It still seems to work fine as it is.
The other day, I bought a couple batteries from Sams Club, both marine AGM. One was a Group 31 replacing the 31 I took off for the house battery. The starting battery I got is a Group 34 replacing a Group 24. The old battery box was broken so I replaced that too.
Here's the house battery.
The battery fit well in the battery box I found.
I mounted the strap to tie it down just inside the compartment.
Everything went together quite well. Here everything is strapped down nicely. With the space inside this compartment, I could probably add a second battery but I'll just stick with one right now.
I started taking things back to the boat to empty out the house. I took the cusions, sails and a few other things.
Another thing I was working on is figuring out the electric bilge pump. I thought the cable had slipped off. I lifted the wood the pump was mounted on to check and saw that the output was broken off and still in the hose. I'm thinking to order a new bilge pump. Then, I can put a more flexible hose on the end so it will not break again. The hose heading to the through-hull is very stiff.
First thing I did was to replace the battery switch. It went pretty good. One cable seemed to be slightly short so it was difficult to reach the connection. Because of how the cables were connected, it ended up being mounted upside down. It still seems to work fine as it is.
The other day, I bought a couple batteries from Sams Club, both marine AGM. One was a Group 31 replacing the 31 I took off for the house battery. The starting battery I got is a Group 34 replacing a Group 24. The old battery box was broken so I replaced that too.
Here's the house battery.
The battery fit well in the battery box I found.
I mounted the strap to tie it down just inside the compartment.
Everything went together quite well. Here everything is strapped down nicely. With the space inside this compartment, I could probably add a second battery but I'll just stick with one right now.
I started taking things back to the boat to empty out the house. I took the cusions, sails and a few other things.
Another thing I was working on is figuring out the electric bilge pump. I thought the cable had slipped off. I lifted the wood the pump was mounted on to check and saw that the output was broken off and still in the hose. I'm thinking to order a new bilge pump. Then, I can put a more flexible hose on the end so it will not break again. The hose heading to the through-hull is very stiff.
Friday, April 20, 2012
Bilge Pump
Did a little bit of work at the boat today. Recently, I took a look at the bilge to see how it looked. I saw there was some nasty looking water down there. The last few trips, I put some fresh water down there to build up enough for the bilge pump to take care of.
Labels:
Bilge,
Bilge Pump,
Nor'sea,
Nor'sea 27,
Rhapsody,
sailboat,
sailing
Subscribe to:
Posts (Atom)










